VTX-WM1 Quick Installation Guide v1.1
VTX-WM1
Web Monitor Card
Quick Installation Guide
IMPORTANT:
This Quick Installation Guide is intended
to help you install a VTX-WM1 card in one
VTX4000 Series amplier. It describes the
connections to be made, which jumpers
need to be set and how to conrm that the
card is working correctly using a laptop (or
other) PC.
This guide does NOT cover the
following topics:
• How to connect multiple VTX-WM1s to
a building-wide network
• How to fully congure the cards for a
particular installation
• How to use the Graphical User
Interface and interpret the amplier
data
For full information on these and other
related topics, please consult the full
VTX-WM1 Installation and User Manual,
which may be downloaded as a PDF
document from www.cloud.co.uk
A short video giving an overview of the
installation of the VTX-WM1 is also available
on the Cloud website. If tting a card for the
rst time, you may nd it helpful to view this
before commencing the installation.
Installing the card in a VTX
Series amplier
1. With the amplier disconnected from
AC mains, remove the top panel. Retain
the screws (eleven plus the transformer
bolt).
2. Remove the rear blanking plate. Retain
the screws.
CHANNE
HANNE
CHANNE
CHANNE
H
H
H
SPEAKER O
0V
H1
V
H2
0V
F
N
F
F
BRIDG
1-2
F
BRIDGE
3-4
4
HM
- MI
3-4
BRIDGE
1-2
3. On the amplier’s upper rear PCB
(Remote Vol PCB, PC331012), locate
the jumpers J109, J209, J309, J409, J110,
J210, J310 and J410. All of these (total
8) should be removed. (Refer to pages
12 &13 of the amplier manual for full
details of amplier jumper locations.)
VTX-WM1 card connectors
VTX amplier upper PCB
4. Note the connector idents on the
VTX-WM1 card. Connect each of
the ying leads as shown in the
following table:
VTX-WM1
CARD
UPPER
REAR PCB
LOWER
PCB
J107B J107A
J207B J207A
J307B J307A
J407B J407A
J805A J805B
J806A J806B
J801A J801B
J802A J802B
5. The VTX-WM1 card sits with the
two support brackets resting on the
heatsinks, and its RJ-45 connector
protruding through the rear panel slot;
secure the card using the two screws
supplied.
6. Plug the unused yellow-red-yellow cable
from the mains transformer into the
3-pin Molex header on the VTX-WM1.
7. Fix the new rear plate (supplied) over
the card slot using the screws removed
in Step 2. Replace the amplier top
cover.
Basic conguration and
checking operation
1. Connect the card’s Ethernet port to the
network port on a laptop (or other)
computer using a standard network
cable. Either a “straight” or a “crossed”
cable may be used, as the VTX-WM1
auto-detects the data lines. Turn the
amplier on. Turn the computer on
and set a static IP address of the form
192.168.0.xxx, where xxx can be any
value between 1 and 254 except 127.
Launch the Internet browser normally
used (e.g., Microsoft Internet Explorer,
Mozilla Firefox, Safari, etc.)
2. Enter the address 192.168.0.127 in
the browser’s URL eld, and the screen
shown below should appear:
The amplier type shown in the
title should be that of the amplier
in use. This conrms that the data
communications section of the card
is operating correctly. The card’s IP
address can be changed subsequently,
and this procedure is covered in the full
Installation and User Manual.
3. Close the browser application.
Disconnect the amplier from the
computer and turn it off.
POWER
CONNECTOR
(20 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce